Datasheet 搜索 > DC/DC转换器 > TI（德州仪器） > LM5008SDCX/NOPB 数据手册 > LM5008SDCX/NOPB 产品设计参考手册 1/6 页
器件3D模型￥ 28.576
LM5008SDCX/NOPB 产品设计参考手册 - TI（德州仪器）
制造商:
TI（德州仪器）
分类:
DC/DC转换器
封装:
WDFN-8
描述:
9.5V 至 95V 宽输入电压、350mA 恒定导通时间非同步降压稳压器 8-WSON -40 to 125
Pictures:
3D模型
符号图
焊盘图
引脚图
产品图
页面导航:
原理图在P2
应用领域在P6
导航目录
LM5008SDCX/NOPB数据手册
Page:
of 6 Go
若手册格式错乱，请下载阅览PDF原文件
User's Guide
SNVA090B–May 2004–Revised April 2013
AN-1330 LM5008 Evaluation Board
1 Introduction
The LM5008 evaluation board is designed to provide the design engineer with a fully functional step down
switching regulator to evaluate LM5008 regulator IC, in a typical environment.
The performance of evaluation board is as follows:
• Input range: 12V to 95V, transients upto 100V (absolute maximum)
• Output voltage: 10V
• Output current: 300mA
• Measured efficiency: 89% at 200mA and V
IN
= 30V
• Board size: 31.9mm x 44.4mm
2 Theory of Operation
The LM5008 step-down switching regulator features all of the functions needed to implement low cost,
efficient, Buck bias regulators. This high voltage regulator contains an 100V, 0.5A N-channel Buck switch.
The regulator is based on hysteretic control scheme using an on-time inversely proportional to input
voltage (V
IN
). This feature allows the operating frequency to remain relatively constant with load and input
voltage variations. The hysteretic control requires no control loop compensation, while providing fast load
transient response. Additional protection features include : Thermal Shutdown, V
CC
undervoltage lockout
and maximum duty–cycle limiter. LM5008 can be used in numerous applications to efficiently regulate step
down higher voltage inputs. This regulator is well suited for 48V telecom and the new 42V automotive
power bus ranges.
The LM5008 operates in discontinuous conduction mode at light load currents or continuous conduction
mode at heavier load currents. In discontinuous conduction mode, current through the output inductor
starts at zero and ramps up to the peak value during the buck switch on time, and then back to zero
during buck switch off time. In discontinuous conduction mode, the operating frequency can be relatively
low and will vary with load. Therefore at light loads the conversion efficiency is maintained , since
switching losses decrease with reduction in switching frequency.
The evaluation board just needs one high voltage power-supply (upto 100V and current rating of 0.5A).
The maximum output power is 3 watts. Either an electronic load or resistor bank can be used for testing
evaluation board.
3 Start-up Feature
There is no soft-start feature in LM5008, and it normally comes up with full load current to supply the
power demanded by the load within a short time. The LM5008 contains an intelligent current limit OFF
timer intended to reduce the foldback characteristic inherent with fixed off-time over-current protection. If
the current in the Buck FET exceeds 550mA the present cycle is immediately terminated (cycle by cycle
current limit). Following the termination of the cycle a non-resetable current limit off timer is initiated. The
duration of off time is a function of the external setting resistor (Rcl) and the FB pin voltage. When FB pin
voltage = 0V the current limit off time is internally preset to 35µs. This condition occurs in short circuit
operation when a maximum amount of off time is required.
In cases of overload (not complete short circuit) the current limit off time can be reduced as a function of
the output voltage (measured at the FB pin). Reducing the off time during smaller overloads reduces the
amount of foldback and also reduces the initial start-up time.
All trademarks are the property of their respective owners.
1
SNVA090B–May 2004–Revised April 2013 AN-1330 LM5008 Evaluation Board
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
器件 Datasheet 文档搜索
AiEMA 数据库涵盖高达 72,405,303 个元件的数据手册，每天更新 5,000 多个 PDF 文件
