Web Analytics
Datasheet 搜索 > 微控制器 > Microchip(微芯) > DSPIC30F2010-20I/SP 数据手册 > DSPIC30F2010-20I/SP 用户编程技术手册 1/66 页
DSPIC30F2010-20I/SP
器件3D模型
15.668
导航目录
  • 引脚图在P2
DSPIC30F2010-20I/SP数据手册
Page:
of 66 Go
若手册格式错乱,请下载阅览PDF原文件
© 2010 Microchip Technology Inc. DS70102K-page 1
dsPIC30F
1.0 OVERVIEW AND SCOPE
This document defines the programming specification
for the dsPIC30F family of Digital Signal Controllers
(DSCs). The programming specification is required
only for the developers of third-party tools that are used
to program dsPIC30F devices. Customers using
dsPIC30F devices should use development tools that
already provide support for device programming.
This document includes programming specifications
for the following devices:
dsPIC30F2010/2011/2012
dsPIC30F3010/3011/3012/3013/ 3014
dsPIC30F4011/4012/4013
dsPIC30F5011/5013/5015/5016
dsPIC30F6010/6011/6012/6013/6014/6015
dsPIC30F6010A/6011A/6012A/6013A/6014A
2.0 PROGRAMMING OVERVIEW
OF THE dsPIC30F
The dsPIC30F family of DSCs contains a region of on-
chip memory used to simplify device programming.
This region of memory can store a programming
executive, which allows the dsPIC30F to be
programmed faster than the traditional means. Once
the programming executive is stored to memory by an
external programmer (such as Microchip’s MPLAB
®
ICD 2, MPLAB
PM3, PRO MATE
®
II, or MPLAB REAL
ICE™), it can then interact with the external
programmer to efficiently program devices.
The programmer and programming executive have a
master-slave relationship, where the programmer is
the master programming device and the programming
executive is the slave, as illustrated in
Figure 2-1.
FIGURE 2-1: OVERVIEW OF dsPIC30F
PROGRAMMING
Two different methods are used to program the chip in
the user’s system. One method uses the Enhanced In-
Circuit Serial Programming™ (Enhanced ICSP™)
protocol and works with the programming executive.
The other method uses In-Circuit Serial Programming
(ICSP) protocol and does not use the programming
executive.
The Enhanced ICSP protocol uses the faster, high-
voltage method that takes advantage of the
programming executive. The programming executive
provides all the necessary functionality to erase,
program and verify the chip through a small command
set. The command set allows the programmer to
program the dsPIC30F without having to deal with the
low-level programming protocols of the chip.
The ICSP programming method does not use the
programming executive. It provides native, low-level
programming capability to erase, program and verify
the chip. This method is significantly slower because it
uses control codes to serially execute instructions on
the dsPIC30F device.
This specification describes the ICSP and Enhanced
ICSP programming methods. Section 3.0
“Programming Executive Application” describes
the programming executive application and
Section 5.0 “Device Programming” describes its
application programmer’s interface for the host
programmer. Section 11.0 “ICSP™ Mode”
describes the ICSP programming method.
2.1 Hardware Requirements
In ICSP or Enhanced ICSP mode, the dsPIC30F
requires two programmable power supplies: one for
V
DD and one for MCLR. For Bulk Erase programming,
which is required for erasing code protection bits, V
DD
must be greater than 4.5 volts. Refer to Section 13.0
“AC/DC Characteristics and Timing Requirements”
for additional hardware parameters.
Programmer
dsPIC30F Device
Programming
Executive
On-chip Memory
2
dsPIC30F Flash Programming Specification

DSPIC30F2010-20I/SP 数据手册

Microchip(微芯)
20 页 / 7.79 MByte
Microchip(微芯)
34 页 / 0.37 MByte
Microchip(微芯)
66 页 / 1.52 MByte
Microchip(微芯)
24 页 / 0.2 MByte
Microchip(微芯)
2 页 / 0.09 MByte
Microchip(微芯)
18 页 / 0.3 MByte
Microchip(微芯)
2 页 / 0.1 MByte
Microchip(微芯)
1 页 / 0.14 MByte

DSPIC30F201020 数据手册

Microchip(微芯)
MICROCHIP  DSPIC30F2010-20E/SO  数字信号控制器, dsPIC30F系列, 80 MHz, 12 KB, 20 输入, I2C, SPI, UART
Microchip(微芯)
MICROCHIP  DSPIC30F2010-20I/SO  数字信号控制器, dsPIC30F系列, 80 MHz, 12 KB, 20 输入, I2C, SPI, UART, 5.5 V
Microchip(微芯)
MICROCHIP  DSPIC30F2010-20I/SP  芯片, 16位20MIPS DSPIC, SPDIP-28
Microchip(微芯)
dsPIC30F1010/202x 16 位数字信号控制器Microchip 的 dsPIC30F 系列数字信号控制器 (DSC) 为设计人员提供有着 MCU 的简便性的 DSP 类似性能。 dsPIC30F1010/202x 系列的设备具有外围设备,以支持数字开关模式电源 (SMPS) 和其他数字电源转换应用。### CPU 功能最大 30 MIPS CPU 速度 改良的哈佛体系结构 经 C 编译器优化的指令集体系结构 83 基座说明,带柔性寻址模式 24 位宽说明,16 位宽数据路径 12 K 字节片上闪存程序空间 512 字节片上数据 RAM 16 x 16 位工作寄存器阵列 32 个中断源 三个外部中断源 每个中断 8 个用户可选优先级级别 4 个处理器例外情况和软件陷阱 ### DSP 引擎功能模块和位倒序模式 两个 40 位宽蓄电池,带可选饱和逻辑 17 位 x 17 位单周期硬件部分/整数倍增器 单周期倍乘 (MAC) 操作 40 级柱式移位器 双数据获取 ### 外围功能高电流汇电流/源电流输入/输出引脚:25 mA/25 mA 三个 16 位计时器/计数器 - 将 16 位计时器配对到 32 位计时器模块的选项 一个 16 位捕获输入功能 两个 16 位比较/PWM 输出功能 四个带 8 个输出的 PWM 生成器 10 位 2000 Ksps 模拟到数字转换器 (ADC) - 6 到 12 通道,具体取决于型号 四个模拟比较器 3 线 SPI 模块 I2CTM 模块 UART 模块 ### dsPIC® 数字信号控制器
Microchip(微芯)
dsPIC30 系列 512 B RAM 12 kB 闪存 16位 数字信号控制器 - QFN-28
Microchip(微芯)
数字信号处理器和控制器 - DSP, DSC 16B MCU DSP 28LD 30MIPS 12KB FLASH
Microchip(微芯)
dsPIC30 系列 512 B RAM 12 kB 闪存 16位 数字信号控制器 - QFN-S28
Microchip(微芯)
Microchip(微芯)
Microchip(微芯)
器件 Datasheet 文档搜索
器件加载中...
AiEMA 数据库涵盖高达 72,405,303 个元件的数据手册,每天更新 5,000 多个 PDF 文件